Please noted that this link is
- Model number: HC960A
- without connector
- crawler mode (details please see below)
NOTE:
Do NOT use it while you charge it
The power wire should not exceed 20cm long
Description:
- Smaller heat generation
- The same quick speed for output of forward and reverse
- It supports tanks, crawlers, cars with differential steering, or boats, which needs two ESCs and the remote controller to be set to mix controlling.
Working modes explanation:
- Crawler mode:
If you decrease the throttle, it decreases the speed correspondingly.
Automatically stop the motor after the throttle is back to the middle.
When the motor rotates forward, if the throttle pulls back, the motor will immediately reverse
- No brake mode:
If you decrease the throttle, the motor decreases the speed correspondingly through inertance.
The motor rotates through inertance after the throttle is back to the middle.
When the motor rotates forward, if the throttle pulls back, the motor will immediately reverse
Specification:
- Model number: HC960A
- Working voltage: 10V-32V (Lipo 3S-7S), supporting 24V storage battery
- Continuous/peak current: 100A/960A forward, 100A/960A reverse
- Size: around 5CM*3.5CM*2.3CM
- Power line and motor line: 12AWG-100mm
- Supporting motors: 540/550/775/795/D848 brushed motors. If the voltage to the power supply is within the rated voltage of the motor, it can connect two motors in parallel connection
- UBEC: 5V 2A (Power supply to the receiver and servo)
- Weight: around 65-70g
- Signal interface: around 20cm long
- Power interface: optional, XT60 or without interface
- Motor interface: optional, XT60 or without interface
Indicator status:
After the ESC is powered on, the indicator light is on and flashes once. The light flashes again when the remote control stroke is in the middle.
If the signal is lost, the indicator light flashes quickly.
Stroke calibration method:
1. Put the stroke of the remote controller to the max
2. Power on the ESC, the indicator light is on and flashes 3. Plug the signal line to the corresponding channel of the receiver.
3. Wait a few seconds, and the indicator flashes twice
4. Put the stroke of the remote controller to the middle, and the indicator flashes three times.
5. Stroke calibration is finished
Package includes:
1PCS ESC
- Model number: HC960A
- without connector
- crawler mode (details please see below)
NOTE:
Do NOT use it while you charge it
The power wire should not exceed 20cm long
Description:
- Smaller heat generation
- The same quick speed for output of forward and reverse
- It supports tanks, crawlers, cars with differential steering, or boats, which needs two ESCs and the remote controller to be set to mix controlling.
Working modes explanation:
- Crawler mode:
If you decrease the throttle, it decreases the speed correspondingly.
Automatically stop the motor after the throttle is back to the middle.
When the motor rotates forward, if the throttle pulls back, the motor will immediately reverse
- No brake mode:
If you decrease the throttle, the motor decreases the speed correspondingly through inertance.
The motor rotates through inertance after the throttle is back to the middle.
When the motor rotates forward, if the throttle pulls back, the motor will immediately reverse
Specification:
- Model number: HC960A
- Working voltage: 10V-32V (Lipo 3S-7S), supporting 24V storage battery
- Continuous/peak current: 100A/960A forward, 100A/960A reverse
- Size: around 5CM*3.5CM*2.3CM
- Power line and motor line: 12AWG-100mm
- Supporting motors: 540/550/775/795/D848 brushed motors. If the voltage to the power supply is within the rated voltage of the motor, it can connect two motors in parallel connection
- UBEC: 5V 2A (Power supply to the receiver and servo)
- Weight: around 65-70g
- Signal interface: around 20cm long
- Power interface: optional, XT60 or without interface
- Motor interface: optional, XT60 or without interface
Indicator status:
After the ESC is powered on, the indicator light is on and flashes once. The light flashes again when the remote control stroke is in the middle.
If the signal is lost, the indicator light flashes quickly.
Stroke calibration method:
1. Put the stroke of the remote controller to the max
2. Power on the ESC, the indicator light is on and flashes 3. Plug the signal line to the corresponding channel of the receiver.
3. Wait a few seconds, and the indicator flashes twice
4. Put the stroke of the remote controller to the middle, and the indicator flashes three times.
5. Stroke calibration is finished
Package includes:
1PCS ESC